Blog | Daiwa Lance International

Top Lance vs Porous Plug Stirring: Choosing a Method for Your Ladle

Written by Author Name | 2026.11.19

Top lance vs porous plug stirring is a comparison of two routes for introducing argon into a ladle: a plug set into the ladle floor that purges from below, or a lance lowered in from above and submerged into the melt. The two are complementary rather than interchangeable, and many plants maintain both.

This article compares how the two stirring methods work, their practical advantages and limitations, and when a top lance is the appropriate choice for a ladle.


The Challenge - The Ladle Must Be Stirred, Whatever The Plug Is Doing

Stirring is not optional in secondary refining. Without it, temperature and composition stay stratified, deoxidation products remain suspended in the steel, dissolved hydrogen and nitrogen stay in solution, and desulfurization stalls as local equilibrium is approached at the slag interface.

That creates an availability problem. If a plant has exactly one route for introducing gas into the ladle, then the condition of that single route determines whether a heat can be treated properly. A blocked plug does not delay the decision - the steel is already in the ladle and losing temperature.

How Does Each Method Deliver Argon?

Bottom porous plug stirring

A bottom purging plug is a permeable refractory element built into the floor of the ladle. Argon is supplied through it from below and rises through the full depth of the bath.

Because gas enters at the deepest point, bubbles travel the maximum available distance before reaching the surface. The plug is part of the ladle lining, so its condition is tied to the ladle refractory campaign rather than managed as a separate consumable.

Top-lance stirring

A top lance approaches from the opposite direction. It is lowered through the open top of the ladle, submerged to the required immersion depth, and releases argon there. When the treatment is finished it is withdrawn.

The Daiwa Argon Stirring Lance is built for this duty in three layers: a calorized steel protective shell, a rich alumina refractory coating specified at Al₂O₃ = 80% and requiring proper drying, and a calorized core steel pipe. Published dimensions are a core pipe outside diameter of 48.6-60.5 mm, wall thickness of 3.6-14.2 mm, core pipe length of 4,000-6,000 mm and total lance length of 5,500-7,550 mm.

Because the lance is a separate item rather than part of the lining, it is managed as a consumable with its own inspection and replacement cycle.

Top Lance Vs Porous Plug Stirring - Side-By-Side Comparison

Characteristic

Bottom porous plug

Top lance

Location

Built into the ladle floor

Lowered in from above, then withdrawn

Gas entry point

Deepest point of the bath

At the selected immersion depth

Relationship to ladle

Part of the refractory lining

Separate consumable item

Replacement

Tied to the ladle refractory campaign

Independent of ladle relining

Availability if the other fails

Not applicable

Provides a route when the plug is blocked or worn

Depth control

Fixed by ladle geometry

Set by how far the lance is lowered

Handling requirement

None during treatment

Manipulator or crane rated for full assembled length

Ladles without bottom purging

Not available

Usable

Neither column is a verdict. The plug's position at the bottom of the bath is a genuine advantage of that route, and the lance's independence from the lining is a genuine advantage of the other. A plant choosing between them is choosing which constraint it prefers to live with and a plant with both is not obliged to choose.

When Is A Top Lance The Right Choice?

Three situations recur across ladle stirring methods.

Plug blockage or failure

Porous plugs block with steel infiltration and wear with use. When one fails, the ladle cannot stir through it, and the options narrow to accepting a compromised heat or holding the ladle while it loses temperature.

A top lance provides a route that does not depend on the plug's condition. That is not a redundancy argument on paper - it is the difference between treating the heat in front of you and downgrading it.

Emergency stirring in secondary refining

Emergency stirring in secondary refining is a listed application of the Daiwa Argon Stirring Lance, alongside dispersing argon to homogenise temperature and composition, removing dissolved gases such as hydrogen and nitrogen, and supporting deoxidation and desulfurization.

The word "emergency" describes the trigger, not the capability. The stirring performed is the same physical process; what differs is that it is available when the primary route is not.

Ladles without bottom purging

Not every ladle in a plant is equipped for bottom stirring. Used bins, transfer bins, and purchased equipment may not have foam plugs. For these, a top lance is not a backup - it is the only available route, and emergency ladle stirring becomes routine practice rather than contingency.

What To Confirm Before Specifying A Top Lance?

  1. Measured ladle depth and freeboard, not values carried from a different vessel.
  2. Required immersion depth for the treatment.
  3. Total lance length from the 5,500-7,550 mm range - not core pipe length, which is 4,000-6,000 mm.
  4. Core pipe dimensions: outside diameter 48.6-60.5 mm, wall thickness 3.6-14.2 mm.
  5. Outlet type: Straight-Through Exit at Ø19.0 mm, Porous Plug Exit, or Tri-Port Exit.
  6. Handling arrangement rated for the full assembled length and weight.

Safety In Use

A top lance introduces handling requirements that a bottom plug does not, because something long, heavy and hot is being moved over an open ladle.

  • Verified refractory condition. Inspect the alumina refractory coating before every use. Cracking or spalling means the lance does not enter the ladle.
  • Uniform wall thickness. With a core pipe wall of 3.6-14.2 mm carrying an assembly up to 7,550 mm long, even wall thickness is what allows the lance to resist bending and breaking while extended over a ladle.
  • Clean, oil-free and grease-free surface. Lances must arrive clean and be stored clean and dry, so contamination is not introduced into the melt.
  • Rigorous quality control. Daiwa lance products are manufactured under ISO 9001 quality management and ISO 14001 environmental management, and inspected to JIS.

Confirm immersion depth against measured ladle depth before lowering rather than judging it during the operation. Handling equipment must be rated for the full assembled length. Personal protective equipment and adequate ventilation are required for heat and fumes.

Common Mistakes To Avoid

  • Treating the two methods as alternatives when the practical question is whether to hold both capabilities.
  • Discovering that no top-lance capability exists at the moment a plug fails.
  • Sizing a lance from a different ladle's dimensions.
  • Working from core pipe length rather than total lance length when checking fit.
  • Assuming handling equipment rated for shorter items will manage a 7,550 mm assembly.
  • Returning a lance to service without inspecting the refractory coating.

Manufacturing Standards Behind The Quality

Daiwa lance products are manufactured in Tan Thuan Export Processing Zone, District 7, Ho Chi Minh City, Vietnam, using Japanese steel-tube manufacturing technology and engineering discipline, backed by JIS. Quality management follows ISO 9001 and environmental management follows ISO 14001.

The company exports to more than 52 countries with full export documentation. For an item held partly as insurance against plug failure, availability and documentation reliability are part of the specification rather than commercial detail.

Conclusion

Framing top lance vs porous plug stirring as a contest misses what matters operationally. The plug enters gas at the deepest point and needs no handling during treatment; the lance works independently of the lining and can be lowered to a chosen depth. What determines whether a heat is treated properly is not which method is theoretically better, but whether a working route exists on the day. Specify against measured ladle dimensions, and decide deliberately whether one route is enough.

Bottom porous plugs cannot always consistently meet the stirring requirements of secondary refining. The Daiwa Argon Stirring Lance provides a top-stirring solution independent of the porous plug system; it is suitable for emergency stirring, for ladles lacking bottom-blowing capabilities, or as a backup when porous plugs become clogged or worn. Contact Daiwa Lance for advice on the appropriate length, immersion depth, and nozzle type for your specific ladles, or request a quote to ensure you have stirring capabilities ready when needed.

FAQs

Is a top lance better than a bottom porous plug?

Neither is universally better; they are complementary. A plug introduces gas at the deepest point of the bath and requires no handling during treatment. A lance works independently of the ladle lining, can be lowered to a selected depth, and remains available when a plug is blocked or worn. Many plants maintain both.

Can a top lance be used on a ladle with no bottom plug?

Yes. A top lance is lowered through the open top of the ladle and does not depend on any fitting in the floor. For older vessels, transfer ladles or units without bottom purging, it is the available stirring route rather than a backup.

What happens if a porous plug blocks mid-campaign?

Stirring through that route stops, and the plant must either accept a compromised heat or hold the ladle while it loses temperature. A top lance provides an independent route, which is why emergency stirring in secondary refining is listed among the applications of the Daiwa Argon Stirring Lance.

What length of lance is needed?

Total lance length is selected from the 5,500-7,550 mm range against measured ladle depth, freeboard and required immersion depth. Note that core pipe length is a different figure - 4,000-6,000 mm and should not be used when checking whether a lance suits a particular ladle.

Does a top lance require special handling equipment?

It requires handling rated for the full assembled length and weight, since an assembly up to 7,550 mm long is moved over an open ladle. Confirm manipulator or crane compatibility at specification stage rather than on delivery, together with immersion depth against measured ladle depth.

Related Blogs & Pages

  1. Website: https://www.daiwalance.com.vn/
  2. Catalogue page: https://www.daiwalance.com.vn/catalogue 
  3. Contact page: https://www.daiwalance.com.vn/contact 
  4. What is The Structure of Argon Stirring Lance ?: https://www.daiwalance.com.vn/blog/what-is-the-key-properties-of-argon-stirring-lance
  5. Why is The Argon Stirring Lance Used As An Emergency Lance in Steelmaking?: https://www.daiwalance.com.vn/blog/why-is-the-argon-stirring-lance-used-as-an-emergency-lance-in-steelmaking
  6. Improving Steel Quality Through Daiwa Argon Stirring Lance: https://www.daiwalance.com.vn/blog/improving-steel-quality-through-daiwa-argon-stirring-lance
  7. Desulfurization In Ladle Refining Furnace: https://www.daiwalance.com.vn/blog/desulfurization-in-ladle-refining-furnace

About Daiwa Lance

Established since 1997, Daiwa Lance has positioned ourselves as a pioneer in thermic cutting and oxygen lancing technology. Based in Ho Chi Minh City, Vietnam, we have been providing quality customer service and products with advanced Japanese technology.

We maintain the highest quality standards with ISO 9001:2015, ISO 14001:2015, and JIS G standards certifications. We have also expanded our reach globally, exporting to over 55 countries worldwide.

Visit us through our contact channels today: Email, WhatsApp, Contact Us form, or connect with us on Youtube, LinkedIn and Facebook.