Blog | Daiwa Lance International

Argon Stirring Lance Sizes: How to Specify One for Your Ladle

Written by Author Name | 2026.11.19

Argon stirring lance sizes are defined by four published figures: core pipe outside diameter 48.6–60.5 mm, core pipe wall thickness 3.6-14.2 mm, core pipe length 4,000-6,000 mm and total lance length 5,500-7,550 mm. The correct combination is determined by measured ladle depth, required immersion depth and the reach of the handling equipment.

This guide outlines the published size range, explains how to determine the right dimensions for your ladle, and highlights the key details to include when requesting a quotation.

The Challenge - Lance Length Has To Match Ladle Depth And Handling Gear

A stirring lance sits between two fixed constraints. It must reach far enough into the ladle to release argon at the required depth, and it must be handled by equipment that already exists on the shop floor.

Get it too short and the outlet sits above the intended immersion depth, changing the treatment. Get it too long and the assembly becomes awkward to manoeuvre, heavier at the extended position, and possibly incompatible with the manipulator.

Neither error is discovered on paper. Both are discovered on the ladle, with steel already tapped.

Argon Stirring Lance Sizes In Full

Parameter

Published range

Notes

Core pipe outside diameter

48.6-60.5 mm

Carries argon from the supply connection to the outlet

Core pipe wall thickness

3.6-14.2 mm

Governs rigidity of the assembly

Core pipe length

4,000-6,000 mm

Not the figure to use for ladle fit

Total lance length

5,500-7,550 mm

Use this figure for ladle fit and handling

Refractory

Rich alumina, Al₂O₃ = 80%

Requires proper drying

Protective shell

Calorized steel casing

Outer layer

Core pipe treatment

Calorized

Same treatment as the shell

Outlet options

Straight-Through Exit Ø19.0 mm, Porous Plug Exit, Tri-Port Exit

Tri-Port Exit described as highly customised

Core pipe - Outside diameter 48.6-60.5 mm and wall 3.6-14.2 mm

The core pipe is the gas-carrying element. Its outside diameter spans 48.6-60.5 mm across the range.

Wall thickness spans 3.6-14.2 mm - nearly a factor of four between the thinnest and thickest options. That breadth exists because a longer assembly carrying more refractory needs more section to stay rigid while extended over a ladle. Wall thickness is therefore not an independent choice; it follows from the length and configuration selected.

Core pipe length 4,000-6,000 mm

This is the length of the pipe itself, not the assembled lance.

Total lance length 5,500-7,550 mm

This is the complete assembly and the figure that determines whether a lance suits a particular ladle. The difference between the two figures - 1,500 mm at the lower end of the range and 1,550 mm at the upper end - accounts for the assembly beyond the pipe.

Confusing the two is the most common specification error on this product. A lance ordered against core pipe length will be shorter than expected.

How To Work Out The Size You Need?

Step 1 - Measure ladle depth and freeboard

Measure the vessel you will actually use. Ladle depth changes with relining, and freeboard changes with fill practice. Values carried from another vessel, or from the drawing rather than the vessel, are the usual source of sizing errors.

Record both the internal depth and the freeboard available above the steel level at treatment.

Step 2 - Choose immersion depth

Immersion depth is the distance the outlet sits below the steel surface during treatment. This is a process decision made by the metallurgical team, not a procurement assumption.

Step 3 - Select outlet type

Three options are available: the Straight-Through Exit at Ø19.0 mm, the Porous Plug Exit and the Tri-Port Exit. The Tri-Port Exit is documented as highly customised.

Select this together with length rather than afterwards, since a custom argon stirring lance configuration may affect what is achievable within a given assembly length.

Step 4 - Confirm handling and manipulator fit

Check that existing handling equipment can manage the full assembled length and weight, and that the lance can be positioned over the ladle without obstruction. An assembly up to 7,550 mm long moved over an open ladle imposes real constraints on crane geometry and headroom.

Confirm this before ordering. Discovering a clearance problem on delivery is an expensive way to learn ladle house dimensions.

What To Include In An Enquiry?

A complete enquiry allows a manufacturer to quote once rather than exchange several rounds of questions:

  1. Measured ladle internal depth and freeboard - stated as measured, with the date of the last reline if known.
  2. Required immersion depth for the treatment.
  3. Total lance length required, from the 5,500-7,550 mm range.
  4. Core pipe outside diameter, from the 48.6-60.5 mm range, if the plant has a preference.
  5. Wall thickness requirement if rigidity has been an issue previously; otherwise leave it to the manufacturer to size against the length.
  6. Outlet type, with any customisation described explicitly.
  7. Handling arrangement - crane or manipulator type, available headroom, maximum handling weight.
  8. Quantity and intended usage rate, which affects how the plant should hold stock.

Safety In Use

Sizing is a safety exercise as much as a process one. A lance that does not fit the ladle or the handling gear creates hazard before it creates a process problem.

  • Verified refractory condition. Inspect the alumina refractory coating before every use. Cracking or spalling means the lance does not enter the ladle.
  • Uniform wall thickness. With a core pipe wall of 3.6-14.2 mm carrying an assembly up to 7,550 mm long, even wall thickness is what allows the lance to resist bending and breaking while extended over a ladle. This is the direct link between the dimension on the order and the behaviour in the operator's hands.
  • Clean, oil-free and grease-free surface. Lances must arrive clean and be stored clean and dry, supported along their length rather than at the ends.
  • Rigorous quality control. Daiwa lance products are manufactured under ISO 9001 quality management and ISO 14001 environmental management, and inspected to JIS.

Confirm immersion depth against measured ladle depth before lowering. Handling equipment must be rated for the full assembled length. Personal protective equipment and adequate ventilation are required for heat and fumes.

Common Mistakes To Avoid

  • Ordering against core pipe length (4,000-6,000 mm) instead of total lance length (5,500-7,550 mm).
  • Using ladle dimensions from a drawing rather than from the vessel as currently lined.
  • Treating immersion depth as a procurement assumption rather than a metallurgical decision.
  • Selecting outlet type after length has been fixed.
  • Confirming handling compatibility only on delivery.
  • Repeating a previous order specification after the ladle has been relined or replaced.

Manufacturing Standards Behind The Quality

Daiwa Lance products are manufactured in Tan Thuan Export Processing Zone, District 7, Ho Chi Minh City, Vietnam, using Japanese steel-tube manufacturing technology and engineering discipline, backed by JIS. Quality management follows ISO 9001 and environmental management follows ISO 14001.

The company exports to more than 52 countries with full export documentation. For a configured product, documentation that records the exact dimensions supplied is what makes a repeat order reproducible - particularly where the original specification exercise was carried out by someone who has since moved on.

Conclusion

Argon stirring lance sizes are published as ranges because the product is configured to a ladle rather than sold from a shelf. Work from measured ladle depth, treat immersion depth as a metallurgical decision, select outlet type alongside length rather than after it, and confirm handling compatibility before the order rather than on delivery. Above all, specify against total lance length of 5,500-7,550 mm - not core pipe length.

Need to determine the correct dimensions for your steel ladle argon stirring lance? Simply provide the ladle depth, required immersion depth, and lifting equipment specifications. The Daiwa Lance team can recommend the appropriate configuration and provide a quote based on your specific requirements. Contact us today for a quote.

FAQs

What are the published dimensions of a Daiwa Argon Stirring Lance?

Core pipe outside diameter 48.6-60.5 mm, core pipe wall thickness 3.6-14.2 mm, core pipe length 4,000-6,000 mm and total lance length 5,500-7,550 mm. The lance is built from a calorized steel shell, a rich alumina refractory coating at Al₂O₃ = 80% and a calorized core steel pipe.

Should I specify core pipe length or total lance length?

Total lance length, from the 5,500-7,550 mm range. Core pipe length of 4,000-6,000 mm refers only to the gas-carrying pipe, while total lance length covers the complete assembly and therefore determines reach and handling requirements. Confusing the two is the most common specification error on this product.

Why is the wall thickness range so wide?

Because wall thickness follows from length and configuration. A longer assembly carrying more refractory needs more section to remain rigid while extended over a ladle. The 3.6-14.2 mm range reflects that dependency, so wall thickness is normally left to the manufacturer to size against the specified length unless rigidity has been an issue previously.

What immersion depth should be used?

That is a metallurgical decision for the plant, not a procurement assumption. Daiwa publishes no recommended immersion depth or depth-to-ladle ratio, so the value must come from the plant's own practice or from a cited process reference. It should be settled before length is specified, since it drives the length calculation.

What should an enquiry contain?

Measured ladle depth and freeboard, required immersion depth, total lance length required, core pipe diameter preference if any, outlet type with any customisation described, handling arrangement including available headroom and maximum handling weight, and expected quantity and usage rate.

Related Blogs & Pages

  1. Website: https://www.daiwalance.com.vn/
  2. Catalogue page: https://www.daiwalance.com.vn/catalogue 
  3. Contact page: https://www.daiwalance.com.vn/contact 
  4. What is The Structure of Argon Stirring Lance ?: https://www.daiwalance.com.vn/blog/what-is-the-key-properties-of-argon-stirring-lance
  5. Why is The Argon Stirring Lance Used As An Emergency Lance in Steelmaking?: https://www.daiwalance.com.vn/blog/why-is-the-argon-stirring-lance-used-as-an-emergency-lance-in-steelmaking
  6. Improving Steel Quality Through Daiwa Argon Stirring Lance: https://www.daiwalance.com.vn/blog/improving-steel-quality-through-daiwa-argon-stirring-lance
  7. Desulfurization In Ladle Refining Furnace: https://www.daiwalance.com.vn/blog/desulfurization-in-ladle-refining-furnace

About Daiwa Lance

Established since 1997, Daiwa Lance has positioned ourselves as a pioneer in thermic cutting and oxygen lancing technology. Based in Ho Chi Minh City, Vietnam, we have been providing quality customer service and products with advanced Japanese technology.

We maintain the highest quality standards with ISO 9001:2015, ISO 14001:2015, and JIS G standards certifications. We have also expanded our reach globally, exporting to over 55 countries worldwide.

Visit us through our contact channels today: Email, WhatsApp, Contact Us form, or connect with us on Youtube, LinkedIn and Facebook.